Timber layers can be stacked side by side
Parquet. Construction, Ash Grove whatsapp whiney parquet floor laying, selection suggestions- Do you remember that we talked about a huge floor? So she has a cousin-parquet. Only the solid board is completely uniform, it is a solid (non-plywood) board made of solid wood. Parquet flooring is a three-layer (rarely two-layer) structure made of natural wood. It appeared in the 41st of the 21st century. On the one hand, it resembles a huge size. On the other hand, due to the pattern of the top layer, parquet floors can mimic parquet floors. The relatively new material is also environmentally friendly and completely natural, equally beautiful, durable and wear-resistant, and with proper care, it is also very durable. In addition, it is easier to install, lighter, thinner and finally cheaper. In Europe today, 61% of wood floors are parquet.
The main body of modern parquet is composed of three layers. Also called finishing, front or worker), the thickness is 0.5 to 4-6 mm. It is a thin cut of precious wood that can be used to produce parquet floors: from traditional oak, beech, maple, walnut, birch and cherry to exotic species-wenge, jatoba, teak acacia, dusi . It is this layer that determines the appearance, and most importantly, the durability of the parquet: the thicker it is, the stronger the polishing effect it will withstand. The middle layer consists of short, flat strips (sheets, boards) made of resin conifers glued together. But it happens that the middle layer is made of durable (thin sheet pressed from finely ground wood) and is even less prone to deformation. On the horizontal plane of the middle layer, ridges are arranged along both sides, and grooves are arranged along the other two sides. The components of the locked (no glue) connection are also positioned. The board is fixed on four sides.

The bottom layer is usually 2 spruce or pine plywood. The fibers of the middle layer cross the fibers of the upper layer, and the fibers of the lower layer cross the fibers of the upper layer. The mutually perpendicular layers limit each other's linear expansion, and the plate gains resistance to deformation under the influence of fluctuations in temperature and humidity conditions.

According to the number of rows of dice placed next to each other on the parquet floor, it can be three rows (consisting of three parallel precious wood strips. Usually, all the boards on the board are divided into modules, that is, they are not Placed in continuous strips, but divided into several small parts), double rows (composed of wide strips of veneers, placed in solid strips or divided into modules) and single strips (made to produce solid floors Full effect). These are the most common options. And unlike the parquet floor used on site, it is also in production under certain conditions. This is a more wear-resistant varnish layer. Another option is possible-when the tree is not varnished, but impregnated with a mixture of oil, wax and natural resin. Then, the color and texture of the wood became particularly interesting-rich tones and clear texture patterns appeared. This kind of wooden floor is very easy to install, no need to dry, trim or sand after installation. You can lay it in several ways. During work, in a room with a wooden floor, it should not be hot, cold (+21±2°) and not too dry (relative humidity-from 31% to 61%). Floor-when the planks are not fixed to the base, but simply placed on a special thin substrate and only connected to each other: with glue (to stick the comb into the groove) or without glue (with special connections and help) . You can lay the floor by yourself without inviting the owner, and you can save a lot of money (the cost of laying parquet is 8-11 USD/m²). Just read the instructions in the material data sheet and strictly follow all simple rules. For example, by moving all the furniture to one wall of the room, you can start laying from another wall, and when you reach the middle of the room, rearrange the furniture on the new coating and complete the installation.

Put the polyethylene film between the wooden board and the screed. In order to enhance the sound insulation effect, a layer of polyethylene foam (or pressed cork) is laid on the film. If the seams should be glued together, it can be done in two ways: applying the adhesive to one side (lower part) of the groove, or both, and not to the bottom of the groove or ridge. An expansion joint must be left between the wall and the edge of the board, usually at least 11 mm. As a result, subject to changes in temperature and humidity conditions, nothing hinders the formation of assembled panels in all four directions. If any piece of the floor is badly worn or damaged over time, it is easier to replace these boards, because it takes several hours to disassemble the floor at the seams of the castle, insert new boards and reassemble them. When you move to a new apartment, you can even take it with you, or transfer it from one room to another. The strength of the glueless connection is higher than the strength of the glued connection-over time, the lock will not even form a slight gap. In the 20th century, a parquet floor was invented in which the boards were connected only by gluing, and the non-gluing method was relatively new. The traditional fixing method-glued to the base-is completely similar to the fixing technique of parquet floors. When pasting, you need a smoother foundation than laying, and the moisture content must be stable. Therefore, the screed that has been manufactured by the constructor should be saturated with the penetrating primer, or in extreme cases should be replaced with a new primer. If the concrete under the parquet floor is likely to become wetter, a steam and waterproof layer (a 0.2 mm thick film) must be laid under the floor. Naturally, the wood board cannot be glued to the film, so place an intermediate layer between it and the parquet floor-it is 13 mm plywood or 21 mm particle board. You can provide extra sound insulation for wooden floors by laying a layer of expanded polyethylene, pressed cork or rubber sheets.

Parquet floors can be placed on logs and beams. This is especially true for country houses. The beams and joists must be dry and not sag, otherwise the floor will start to creak. The space under them should be well ventilated to prevent the accumulation of water vapor. The distance between the beam and the log should be at least 61 cm, and the thickness of the parquet floor should be 23 or 26 mm. If the ceiling and threshold height allow, you can pre-lay plywood on the log, and then you can lay the plank on the wooden board. You can use nails to fix the boards directly on the logs, or you can use staples to shoot the boards out (insert them diagonally into your tongue).
You can match the floor to almost any interior design very precisely. The surface pattern depends on the incision and can range from uniform to complex, with knots and veins. Modern wood processing methods have also increased the scope of decoration. Steaming (for beech) enhances the color of natural wood and at the same time increases the stability of the material. After bleaching (oak, maple, beech), the boards acquire a light, cool tone. It is artificial aging. This is how oak products have been processed to give them a noble and deep colonial style parquet. -This is to use a hard metal brush to comb weak fibers. As a result, the surface becomes textured, ribbed and very suitable for country style. The durability of such a board is increased and it can be placed in a high-load public area on the floor.

Large ready-made parquet floors can be installed in any existing order-or. However, in today's practice, we mainly see all the same installations, parallel to the wall or diagonal.
Each company-parquet manufacturer declares the service life of its product (this period can be 21 years or longer). First, this involves the wear of the varnish coating and the amount of polish that the parquet can withstand. For example, a parquet floor with a 4 mm working layer can be sanded up to 5 times. If this procedure is performed every 5 years and 0.5 mm of wood is removed by polishing, the parquet floor can be used for at least 21-26 years.

For boards with a thin working layer, sanding is not provided, but the surface is likely to be polished multiple times. No need to wait for the varnish layer to wear and touch the wood. Just lightly sand the old varnish, then clean the floor with a vacuum cleaner, and then roll up the new layer with a roller.

Parquet, depending on the model, top wood and grade, ranges from $21-61 to $96-111. There is a tree of exotic species that is more expensive. A working layer made of veneer veneer (such as a solid board) is 1.5 times more expensive than a board made of the same wood but with an inlaid working layer (made by bonding rows of wooden boards). The fashion trend tends towards the homogeneity of the floor, tending towards large textures rather than small patterns.

After appreciating the color and pattern of your favorite parquet floor, you should also pay attention to the hardness and wear resistance of the top layer to find out whether the coating meets the operating conditions, especially if the coating should be placed in a heavy load area. Professionals promise to deliver and arrange in the best way. Everything is fine, there is no squeaky noise, the moisture does not pass through, and the walking is very pleasant (bought it).
This article is full of enthusiasm and praise, but the parquet floor owners (I only rely on the comments of friends), the craftsmen who are now doing repairs in my apartment, and, strangely, the shop sellers, all agree that the performance Poor characteristics. height. Scratches and dents will appear immediately, especially in the case of deformable furniture. The administrator will review all messages and delete them if the rules are violated, without warning or explanation. In order to extend the service life, the floor was repaired. Building a Rock Pizza Oven! | Primitive Cooking at the off Grid Cabin